Reset Procedures
Tools Needed:
- None required for basic reset
- Soft cloth for control panel
- Safety gloves (optional)
Step-by-Step Reset Procedures
- Basic Power Reset: Turn off the dishwasher at the circuit breaker or unplug it from the power outlet for 2-5 minutes, then restore power.
- Control Panel Reset: Press and hold the "Heated Dry" and "Start" buttons simultaneously for 3-5 seconds until all lights flash.
- Factory Reset: Press and hold "Heated Dry" and "Normal Cycle" buttons for 10 seconds until control panel resets to factory settings.
- Drain Reset: If dishwasher won't drain, press "Cancel/Drain" button for 3 seconds to initiate drain cycle reset.
- Water Supply Reset: Check water supply valve is fully open and water pressure is adequate (20-120 psi).
- Filter Reset: Clean the filter assembly and reset by running a rinse cycle to clear any blockages.
- Test Run: After reset, run a quick rinse cycle to verify proper operation and reset completion.
Error Codes
| Model Series | KDTE204KPS / KDTM404KPS |
| Type | Built-in Dishwasher |
| Control Type | Electronic Touch Controls |
| Reset Method | Multiple button combinations |
| Power Requirements | 120V, 60Hz, 15A |
| Water Pressure | 20-120 psi |
| Water Temperature | 120°F minimum |
Common Error Codes and Reset Procedures
- F1/E1: Water heating issue - Reset by power cycling and checking heating element
- F2/E2: Water fill timeout - Reset water supply and check inlet valve
- F3/E3: Water leak detected - Reset after checking for leaks and drying interior
- F4/E4: Overflow condition - Reset drain system and check float switch
- F5/E5: Temperature sensor failure - Reset and run diagnostic cycle
- F6/E6: Motor control board error - Reset power completely
- F7/E7: Heater relay fault - Reset and check heating circuit
For persistent error codes, contact KitchenAid Customer Service at 1-800-422-1230 or visit KitchenAid.com
Troubleshooting
| Problem | Possible Cause | Reset Solution |
|---|---|---|
| Dishwasher won't start | Power issue, door not latched, control lock activated | Power reset, ensure door closure, disable control lock |
| Poor cleaning results | Spray arm obstruction, clogged filter, low water temperature | Reset after cleaning spray arms and filter, check water heater |
| Water not draining | Drain hose clogged, air gap blockage, pump issue | Reset drain system, clear obstructions, check pump |
| Leaking water | Door seal failure, loose connections, overfilling | Reset after checking seals and connections |
| Unusual noises | Foreign objects in pump, spray arm obstruction | Reset after removing obstructions and checking components |
| Error codes displayed | Sensor failure, component malfunction, power surge | Perform appropriate reset procedure for specific error code |
Advanced Reset Procedures
- Hard Reset: Disconnect power for 30 minutes to clear all electronic memory
- Diagnostic Mode: Press "Heated Dry" + "Normal" + "Start" simultaneously for service diagnostics
- Software Reset: Contact service for firmware updates and software resets
- Component Reset: Individual component resets may require professional service
Maintenance
Regular Filter Cleaning
Clean the filter assembly monthly by removing, rinsing under warm water, and reinstalling properly to maintain optimal performance and prevent reset requirements.
Spray Arm Maintenance
Regularly inspect and clean spray arms to ensure proper water distribution and prevent cleaning issues that may require system resets.
Door Seal Inspection
Check door seals for wear or damage monthly to prevent leaks and error codes that necessitate reset procedures.
Drain System Maintenance
Keep drain system clear of debris and run monthly cleaning cycles to prevent drain-related resets and error codes.
Control Panel Care
Keep control panel clean and dry to prevent accidental button presses and ensure reliable reset operations when needed.
Monthly Reset Prevention
Perform regular maintenance tasks to minimize the need for reset procedures and ensure consistent dishwasher performance.
Preventive Maintenance Schedule
Daily
Wipe control panel, check for error codes, ensure proper door closure
Weekly
Inspect spray arms, check for leaks, verify proper drainage
Monthly
Clean filter assembly, inspect door seals, run cleaning cycle
Quarterly
Check water connections, inspect drain hose, verify heating performance
Annually
Professional inspection, component testing, software updates
As Needed
Reset procedures when error codes appear or performance issues occur
Manual Downloads
Current Model Manuals
KDTE204KPS
24" Top Control Dishwasher
KDTM404KPS
24" Front Control Dishwasher
KDPE234GPS
24" Panel Ready Dishwasher
KDFE104DSS
24" Built-in Dishwasher
Popular Previous Models
KUDK03CTSS
24" Stainless Steel Dishwasher
KUDC10FXSS
24" Front Control Dishwasher
KUDE48FXSS
48" Double Drawer Dishwasher
KUDL23IXSS
24" Integrated Dishwasher