Reset Procedures
Tools Needed:
- None required for basic reset procedures
- Voltage tester (for advanced troubleshooting)
- Multimeter (optional)
Step-by-Step Reset Procedures
- Basic Power Reset: Turn off the dishwasher at the circuit breaker or unplug it from the power outlet for 5 minutes, then restore power.
- Control Panel Reset: Press and hold the "Start" and "Heated Dry" buttons simultaneously for 3 seconds until all lights flash.
- Factory Reset: Press and hold "Heated Dry" and "Sani Rinse" buttons for 10 seconds until control panel beeps twice.
- Drain Pump Reset: Press "Cancel/Drain" button for 3 seconds to reset drain pump and clear any blockages.
- Heating Element Reset: Turn off power, wait 30 minutes, then restore power to reset thermal protection.
- Water Fill Reset: Close the door and press "Start" to reset water fill sensor and begin new cycle.
- Complete System Reset: Disconnect power for 15 minutes, then run a rinse cycle to reset all systems.
Error Codes
| Model Series | KDTE104DSS / KDTM354DSS |
| Type | Built-in Dishwasher |
| Control Type | Electronic Touch Controls |
| Power Requirements | 120V, 60Hz, 15A |
Common Error Codes
- F1E1: Water heating timeout - Check heating element and thermostat
- F2E1: Water not heating - Verify power supply and heating element
- F3E1: Water temperature sensor failure - Replace temperature sensor
- F4E1: Water fill error - Check water supply and inlet valve
- F5E1: Drain pump error - Clear drain hose and check pump
- F6E1: Motor circuit error - Contact service technician
- F7E1: Communication error - Reset control board
- F8E1: Door switch error - Ensure door is closing properly
Warranty Information
- Full Warranty: 1 year parts and labor
- Extended Warranty: Optional 2-5 year coverage available
- Motor Warranty: 10 years on wash motor
For warranty service, contact KitchenAid Customer Service at 1-800-422-1230 or visit KitchenAid.com
Common Issues
Dishwasher Won't Start
Common causes include door not latched properly, power supply issues, or control panel lock. Perform basic power reset and check door alignment.
Poor Cleaning Results
Often caused by clogged spray arms, improper loading, or hard water buildup. Clean filter system and ensure proper detergent usage.
Water Not Draining
Check for drain hose kinks, clogged filter, or faulty drain pump. Perform drain reset and inspect drainage system.
Leaking Water
Inspect door gasket, check water inlet connections, and ensure proper loading. Door seal replacement may be necessary.
Unusual Noises
Grinding or rattling sounds may indicate foreign objects in pump or worn wash arm bearings. Inspect and clean interior components.
Error Code Display
When error codes appear, note the specific code and perform corresponding reset procedure before calling for service.
Troubleshooting Procedures
Power Issues
Check circuit breaker, ensure proper outlet function, verify power cord connection
Water Fill Problems
Verify water supply valve is open, check inlet hose for kinks, inspect water inlet valve
Drainage Issues
Clear drain hose obstructions, clean filter system, check drain pump operation
Heating Problems
Verify heating element function, check thermostat, ensure proper cycle selection
Control Panel Errors
Perform control reset, check for button responsiveness, verify display function
Door Seal Issues
Inspect gasket for damage, ensure proper door alignment, check latch mechanism
Maintenance
| Maintenance Task | Frequency | Procedure |
|---|---|---|
| Filter Cleaning | Monthly | Remove and rinse filter assembly under running water |
| Spray Arm Inspection | Quarterly | Check for clogs and ensure free rotation of spray arms |
| Door Gasket Cleaning | Monthly | Wipe door gasket with damp cloth to remove food debris |
| Interior Cleaning | Monthly | Run empty cycle with dishwasher cleaner or vinegar |
| Drain Hose Check | Annually | Inspect drain hose for kinks or obstructions |
| Detergent Dispenser | Monthly | Clean detergent dispenser to prevent clogs |
Preventive Maintenance Tips
- Regular Filter Cleaning: Prevents poor cleaning performance and drainage issues
- Proper Loading: Ensures optimal water circulation and cleaning effectiveness
- Use Recommended Detergent: Prevents excessive suds and mechanical issues
- Rinse Aid Usage: Improves drying performance and prevents spotting
- Water Temperature: Maintain 120°F water temperature for optimal cleaning
- Monthly Cleaning Cycle: Run empty cycle with cleaner to remove buildup
Manual Downloads
Current Model Manuals
KDTE104DSS
24" Built-in Dishwasher
KDTM354DSS
Top Control Dishwasher
KDFE104DSS
Front Control Dishwasher
KDPE234GPS
Professional Series
Popular Previous Models
KUDK03CTSS
Classic Series Dishwasher
KUDE48FXSS
Elevate Series Dishwasher
KUDC25FXSS
Contemporary Series
KUDL23FXSS
Low-Profile Series